P3 brake controller




Article Navigation:
  • Photo
  • Video
  • RELATED PAGES
  • Amazon's Choice for "tekonsha prodigy p3 trailer brake controller" Tekonsha Primus IQ Electronic Brake Control. Tekonsha Prodigy P2 Electronic Brake Control.

    Proportional brake controller automatically levels when mounted within a degree vertical range. Includes customizable LCD display, storable settin.

    Tekonsha Prodigy P3 Electronic Trailer Brake Control Controller New. $ Buy It Now. Free Shipping. 19 watching; |; 27 sold. "Boost" feature gives .

    A snap to install with the custom wiring kit. We provide one-on-one, personalized service from the ordering process through the life of your product. Easy installation and adjust to your braking power. The connector you show in your photo is not the connector for installing a brake controller.

    This item qualifies for Free Shipping. Your comment has been submitted successfully. Proportional brake controller automatically levels when mounted within a degree vertical range. Includes customizable LCD display, storable settings, 3 boost levels, battery protection and continuous diagnostics. With a proportional brake controller, you can get heavy-duty emergency braking, general braking or slow-to-an-idle braking for your trailer automatically.

    The intensity with which your trailer brakes are activated and the rate at which they are applied are dependent on the deceleration of your tow vehicle. This means that, unlike time-delay controllers - which send the same amount of preset power to your trailer brakes every time - proportional controllers are able to adapt to every braking situation differently.

    So, if you slam on the brakes in your truck, your trailer brakes will activate with that same extreme intensity. And if you merely slow down as you approach a red light, your trailer will gradually brake in the same manner. Just set the initial power level, select a boost setting, and you're good to go.

    As long as the P3 controller sits level on a horizontal plane and is pointed in the direction of travel, it will sense - via an internal inertia sensor - how your tow vehicle brakes. This inertia-based sensor responds to the deceleration of your tow vehicle as you brake by signaling the controller to send out enough power to your trailer brakes so that they are activated with an intensity that matches.

    The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time. Aside from smoother, more efficient braking, Tekonsha's P3 brake controller also offers a boost feature that gives you more initial braking power for those times when you're towing heavy loads.

    You can switch boost levels so that the power output to your trailer brakes automatically starts out at either 13 percent or 25 percent of the predetermined power setting.

    So, if you boost the initial power so that your trailer brakes activate with 25 percent of the overall intensity at the start, the brakes will reach maximum braking faster. This is particularly beneficial if you are towing a heavy load because the intensity required to stop that load may be far greater than that needed to halt your Infiniti FX Therefore, sending out more initial power to the trailer brakes - and causing them to reach maximum braking faster - allows you to better control the trailer so that it doesn't push your tow vehicle before coming to a complete stop.

    If your trailer weighs less than your tow vehicle , no boost is needed. But if you wish to set the boost so that your trailer leads the braking of your towing setup, you can select level B1. The following table gives an indication of when you might use the different boost levels and the power increases that they offer. But the braking curve for B3 is more aggressive than that of B2. This means that, even though you will start out with the same intensity when using these boost levels, you will get an overall more aggressive braking experience with the higher level.

    So if you use B3, you will reach maximum braking sooner than if you use B2. Customize your P3 and store settings so that you can easily access them later. If you tow multiple trailers, or the same one but with differing loads, store the desired boost and power levels for each so that you don't have to completely reset the controller every time you switch between the trailers. Do other drivers use your towing setup? Customize the P3 display with your desired screen color, brightness and language, and you can easily return it to your preferred settings the next time you tow.

    Tekonsha P-3 Proportional Brake Controller Review - EDUCATIA.INFO



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲